Changsha Tianou Industrial Pump Co.,Ltd.
5 1

Single Suction Multi Stage Water Pump , Low Noise Multi Impeller Centrifugal Pump

Contact Now* Send an Inquiry to this supplier.
or
Start Order * Name your price
You may also be intersted in
multiple stage centrifugal pump

Contact us

Changsha Tianou Industrial Pump Co.,Ltd.
[China]

Address
No.919, North Station Road, Kaifu District, Changsha, Hunan, China Changsha Hunan
Phone
400-1801-181
Contact name
Nick

Quick Information

  • Brand Name: Swan Tianou
  • Place of Origin: China
  • Model Number : DG

Description

High Pressure Horizontal Multistage Centrifugal Pump Single Suction Low Noise

 

Overview:

The DG boiler feed pump is a horizontal single-suction multi-stage segment centrifugal pump. For the transportation of clean water (containing less than 1% of impurities, particle size less than 0.1mm) or other liquids with physical and chemical properties similar to water, suitable for mine drainage, oilfield water injection, factory and urban water supply, drainage, etc. Corrosive, the pump uses different materials, DG boiler feed water pump delivery medium temperature is less than 105 ° C, suitable for a variety of boiler feed water (media temperature if the temperature is 105 degrees, need to change the material, special custom).

 

Structure Type:

The suction port and the spout port of the DG boiler feed pump are vertically upward, and the axial force of the rotor is balanced by the balance disc. The shaft seal can be either a packing seal or a mechanical seal. The rotor supports only DG85-80, DG85-67, DG155-67 with sliding bearings, thin oil lubrication, and other pumps use rolling bearings.

Direction of rotation:

From the motor side, the pump rotates clockwise.

Main parts material:

The pump's over-current components except the DG85-80 and 200DG43 are made of cast steel, and the other pumps are made of cast iron.

Product Range:

Complete supply pump, motor, check valve, gate valve, common base or its own base.

 

 

Item Horizontal multistage centrifugal pump
Suction End
Model D/DG series
Material Cast iron or stainless steel
Color Blue
Mode Horizontal
Drive Coupling
Impeller Close impeller
Seal Pack seal or mechanical seal
Speed 2900r/min,1450r/min
Theory Centrifugal pump
Character High pressure, multistage
Usage Irrigation, high lift and boiler feed
Power Electric or diesel engine
Standard or Non Standard
Shaft Special material shaft
Capacity 46m³/h
Head 50m
Power 5.5-350kw
Warranty 12 months
Certificate ISO9001:2008
OEM Acceptable

 

Pump structure features:

1. The inlet and outlet of the DG boiler pump are vertically upwards. The pump casings such as the inlet section, the middle section, the outlet section and the bearing body of the pump are connected by integral tensioning. The number of stages of the pump is selected based on the lift of the pump.

2. The rotor part of the DG type boiler feed pump is mainly composed of a shaft and an impeller, a bushing, a balance disc and the like mounted on the shaft, wherein the number of impellers depends on the number of stages of the pump. The on-axis parts are fastened with a flat key and a shaft nut to make them integral with the shaft. The entire rotor is supported by rolling bearings or plain bearings at both ends. The bearings are different according to the model and do not bear axial force. The axial force is balanced by the balance disc. The pump allows the rotor to move axially in the pump casing during operation and cannot use radial ball bearings. The rolling bearing is lubricated with grease, the sliding bearing is lubricated with thin oil, and is self-lubricated with an oil ring, and circulated water is cooled.

3. The seal between the inlet section, the middle section and the outlet section of the DG type boiler feed pump is sealed with molybdenum disulfide grease. The seal ring and the vane sleeve are sealed between the rotor part and the fixed part. The degree of wear of the ring and vane sleeves should be replaced when the pump's performance is affected.

4. The seal form of the shaft has two types: mechanical seal and packing seal. When the pump is sealed with packing, the position of the packing ring should be properly placed, and the tightness of the packing must be appropriate, so that the liquid can be oozing one drop at a time. The various sealing components of the pump are installed in a sealed box, and a certain pressure of water is introduced into the tank to perform water sealing, water cooling or water lubrication. A replaceable bushing is provided at the shaft seal to protect the pump shaft.

The secondary high-pressure pump generally adopts sliding bearing and thin oil lubrication structure. The DG85-67 and DG155-67 pumps can be used for sliding bearings and thin oil lubrication. They can also adopt rolling bearing and dry oil lubrication structure. The other models are all equipped with rolling bearings and dry oil lubrication. structure. The main parts of the medium and low pressure pumps are generally made of high quality cast iron, and the main parts of the secondary high pressure pump are made of cast steel or stainless steel.

5. The DG type boiler feed pump is directly driven by the original motor through the elastic coupling. From the direction of the original motor, the pump rotates clockwise.

 

 

 


Product Image

  • Single Suction Multi Stage Water Pump , Low Noise Multi Impeller Centrifugal Pump image

Send an Inquiry to this supplier

Send an Inquiry to this supplier
* From
  To Nick
Changsha Tianou Industrial Pump Co.,Ltd.
* Buying Product
- Please enter your specific buying item.
e.g. 42 inch LCD TV, leather executive chair
Category : Engine Parts
* Message

Use English only Max. 2000 characters. (Min. 20)

Send
EC21.com does not guarantee the validity of product information or the credentials of sellers.